Embark on an enlightening quest, surrounded by the ethereal glow of the 200-301 dumps. Like the ever-changing hues of a kaleidoscope, the 200-301 dumps display a spectrum of practice questions, each one more intriguing than the last. Whether the crystal-clear PDFs paint vivid mental images or the VCE format spins a captivating tale of success, the 200-301 dumps are your sherpa on this spiritual journey. An age-old tome of wisdom, the 200-301 dumps breathe life into arcane knowledge, ensuring no leaf remains unturned. In the sanctity of these resources, we chant our mantra of a 100% Pass Guarantee.
Elevate your chances of acing the 200-301 exam with our expertly-crafted 200-301 VCE and PDF study tools
Question 1:
Which two commands can you use to configure an actively negotiate EtherChannel? (Choose two.)
A. channel-group 10 mode on
B. channel-group 10 mode auto
C. channel-group 10 mode passive
D. channel-group 10 mode desirable
E. channel-group 10 mode active
Correct Answer: DE
Desirable mode: Desirable mode in Port Aggregation Protocol (PAgP) initiates the negotiation and tries to form EtherChannel with other end. Active Mode: Active Mode in Link Aggregation Control Protocol (LACP) initiates the negotiation and tries to form EtherChannel with other end.
Question 2:
Which remote access protocol provides unsecured remote CLI access?
A. console
B. Telnet
C. SSH
D. Bash
Correct Answer: B
Question 3:
What is the primary purpose of a console port on a Cisco WLC?
A. in-band management via an asynchronous transport
B. in-band management via an IP transport
C. out-of-band management via an asynchronous transport
D. out-of-band management via an IP transport
Correct Answer: C
The console port on a Cisco Wireless LAN Controller (WLC) is used for out-of-band management via an asynchronous transport. The console port provides a direct, physical connection to the WLC and can be used for initial configuration, troubleshooting, and recovery in case of network connectivity issues.
In contrast, in-band management refers to the management of the WLC using the same network infrastructure that is used for user traffic. This is typically done via an IP transport, such as SSH or HTTPS, and allows administrators to manage the WLC remotely.
Question 4:
What is a difference between local AP mode and FlexConnect AP mode?
A. Local AP mode creates two CAPWAP tunnels per AP to the WLC
B. Local AP mode causes the AP to behave as if it were an autonomous AP
C. FlexConnect AP mode fails to function if the AP loses connectivity with the WLC
D. FlexConnect AP mode bridges the traffic from the AP to the WLC when local switching is configured
Correct Answer: A
“In local mode, an AP creates two CAPWAP tunnels to the WLC. One is for management, the other is data traffic. This behavior is known as “centrally switched” because the data traffic is switched(bridged) from the ap to the controller where it is then routed by some routing device.”
https://community.cisco.com/t5/wireless-and-mobility/what-s-the-difference-between-local-mode-and-flex-connect-mode/td-p/2532657
Question 5:
What is a characteristic of private IPv4 addressing?
A. simplifies the addressing in the network
B. complies with PCI regulations
C. reduces the forwarding table on network routers
D. is used on hosts that communicate only with other internal hosts
Correct Answer: D
Question 6:
Refer to the exhibit.
After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. What is the reason for the problem?
A. The OSPF router IDs are mismatched.
B. Router2 is using the default hello timer.
C. The network statement on Router1 is misconfigured.
D. The OSPF process IDs are mismatched.
Correct Answer: B
Question 7:
Refer to the exhibit.
An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work. Which additional task allows the two switches to establish an LACP port channel?
A. Change the channel-group mode on SW2 to auto
B. Change the channel-group mode on SW1 to desirable.
C. Configure the interface port-channel 1 command on both switches.
D. Change the channel-group mode on SW1 to active or passive.
Correct Answer: D
Question 8:
DRAG DROP
Drag and drop the IPv4 network subnets from the left onto the correct usable host ranges on the right.
Select and Place:
Correct Answer:
This subnet question requires us to grasp how to subnet very well. To quickly find out the subnet range, we have to find out the increment and the network address of each subnet. Let\’s take an example with the subnet 172.28.228.144/18:
From the /18 (= 1100 0000 in the 3rd octet), we find out the increment is 64. Therefore the network address of this subnet must be the greatest multiple of the increment but not greater than the value in the 3rd octet (228). We can find out the 3rd octet of the network address is 192 (because 192 = 64 * 3 and 192 The network address is 172.28.192.0. So the first usable host should be 172.28.192.1 and it matches with the 5th answer on the right. In this case we don\’t need to calculate the broadcast address because we found the correct answer.
Let\’s take another example with subnet 172.28.228.144/23 -> The increment is 2 (as /23 = 1111 1110 in 3rd octet) -> The 3rd octet of the network address is 228 (because 228 is the multiply of 2 and equal to the 3rd octet) -> The network address is 172.28.228.0 -> The first usable host is 172.28.228.1. It is not necessary but if we want to find out the broadcast address of this subnet, we can find out the next network address, which is 172.28.(228 + the increment number).0 or
172.28.230.0 then reduce 1 bit -> 172.28.229.255 is the broadcast address of our subnet. Therefore the last usable host is 172.28.229.254.
Question 9:
How does CAPWAP communicate between an access point in local mode and a WLC?
A. The access point must not be connected to the wired network, as it would create a loop
B. The access point must be connected to the same switch as the WLC
C. The access point must directly connect to the WLC using a copper cable
D. The access point has the ability to link to any switch in the network, assuming connectivity to the WLC
Correct Answer: D
The access point has the ability to link to any switch in the network, assuming connectivity to the WLC. The AP can be connected to any switch in the network, as long as the switch has connectivity to the WLC. The AP and the WLC exchange CAPWAP messages over IP, using UDP port 5246 or 5247, depending on whether the messages are encrypted.
Question 10:
What Is a syslog facility?
A. Host that is configured for the system to send log messages
B. password that authenticates a Network Management System to receive log messages
C. group of log messages associated with the configured severity level
D. set of values that represent the processes that can generate a log message
Correct Answer: C
A syslog facility is a group of log messages that are associated with a particular configured severity level. Syslog facilities are used to categorize log messages so that they can be filtered and managed more easily. The severity level of a log
message determines how important the message is and how it should be handled.
Option A is incorrect because it describes a syslog host, which is a device that is configured to receive and store syslog messages from other devices.
Option B is incorrect because it describes a password used to authenticate a Network Management System (NMS) to receive log messages, which is not related to syslog facilities.
Option D is incorrect because it describes the syslog process, which is a set of values that represent the processes that can generate a log message, but it is not the same as a syslog facility.
Question 11:
A Cisco engineer must configure a single switch interface to meet these requirements
1.
accept untagged frames and place them in VLAN 20
2.
accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone
Which command set must the engineer apply?
A. switchport mode dynamic desirable switchport access vlan 20 switchport trunk allowed vlan 30 switchport voice vlan 30
B. switchport mode dynamic auto switchport trunk native vlan 20 switchport trunk allowed vlan 30 switchport voice vlan 30
C. switchport mode access switchport access vlan 20 switchport voice vlan 30
D. switchport mode trunk switchport access vlan 20 switchport voice vlan 30
Correct Answer: C
The data vlan is connected to the IP phone. Data VLANs connected to the IP phones are untagged by default.
The IP phone connected to a switchport should learn its vlan using cdp. To configure this, the command is “switchport voice Vlan 30”
https://docs.nvidia.com/networking-ethernet-software/cumulus-linux-40/Layer-2/Link-Layer-Discovery-Protocol/Voice-VLAN/
Question 12:
What is represented by the word “port” within this JSON schema?
A. key
B. value
C. array
D. object
Correct Answer: A
Within this JSON schema, the word “port” is a key within the objects represented by the curly braces {}. Each object in the schema has two key-value pairs, where “port” is one of the keys.
Question 13:
Refer to Itie exhibit
A network engineer started to configure port security on a new switch. These requirements must be met:
1.
MAC addresses must be learned dynamically
2.
Log messages must be generated without disabling the interface when unwanted traffic is seen Which two commands must be configured to complete this task”? (Choose two)
A. SW(config-if)#switchport port-security violation restrict
B. SW(config-if)#switchport port-security mac-address 0010.7B84.45E6
C. SW(config-if)#switchport port-security maximum 2
D. SW(config-if)#switchport port-security violation shutdown
E. SW(config-if)#switchport port-security mac-address sticky
Correct Answer: AE
Question 14:
How does Chef configuration management enforce a required device configuration?
A. The Chef Infra Server uses its configured cookbook to push the required configuration to the remote device requesting updates.
B. The installed agent on the device connects to the Chef Infra Server and pulls its required configuration from the cookbook.
C. The Chef Infra Server uses its configured cookbook to alert each remote device when it is time for the device to pull a new configuration.
D. The installed agent on the device queries the Chef Infra Server and the server responds by pushing the configuration from the cookbook.
Correct Answer: B
Chef configuration management enforces a required device configuration by using an installed agent on the device that connects to the Chef Infra Server and pulls the required configuration from the cookbook.
In Chef, a cookbook is a collection of recipes, attributes, templates, and other configuration files that define a desired configuration for a specific device or group of devices. The Chef Infra Server stores the cookbook, and the installed agent on each device periodically checks in with the server to see if there are any updates to the cookbook.
If an update is available, the agent pulls the updated cookbook from the server and applies the new configuration to the device. This process is known as “pull-based” configuration management, where the devices actively request updates from the server.
Question 15:
What is a function of an endpoint?
A. It is used directly by an individual user to access network services
B. It passes unicast communication between hosts in a network
C. It transmits broadcast traffic between devices in the same VLAN
D. It provides security between trusted and untrusted sections of the network.
Correct Answer: A
An endpoint is a remote computing device that communicates back and forth with a network to which it is connected. Examples of endpoints include: Desktops. Laptops. Smartphones.